Products

This is a test product created automatically by Bold and can be used to test the function of Bold's Shopify app. This is not a real product and should not be purchased in a real order.

Replace that weak oem plastic box with our battery box!  

Included -  oem or vortex cdi mount , tip over sensor mount and starter solenoid mount. Included new battery stay down bracket.   Powder coat finish 

 

 

Did you remove your headlights?    Looking to clean up the front of your quad and remove those ugly plastic brackets?! This is the fix for That! 

New design , and now including shroud/plastic brackets (stronger than oem) 

Uses your oem rubber grommets,  mounting hardware included for the regulator and side mounts.  

 

 

Weld in kit for your 17-20 CRF450R, to convert your frame to accept a 89-2001 Honda CR500 Engine.   

This t-shirt is comfortable, soft, lightweight, and form-fitting. It's an ideal staple piece for any wardrobe!

• 100% combed ring-spun cotton
• Heather Grey is 90% cotton, 10% polyester
• Fabric weight: 4.3 oz/yd² (145.8 g/m²)
• 32 singles
• Pre-shrunk
• Blank product sourced from Honduras, Nicaragua, Mexico, or Cambodia

Size guide

This t-shirt is comfortable, soft, lightweight, and form-fitting. It's an ideal staple piece for any wardrobe!

• 100% combed ring-spun cotton
• Heather Grey is 90% cotton, 10% polyester
• Fabric weight: 4.3 oz/yd² (145.8 g/m²)
• 32 singles
• Pre-shrunk
• Blank product sourced from Honduras, Nicaragua, Mexico, or Cambodia

Size guide

This is an easy and affordable fix to the yfz450r weak stock subframe.  This will prevent bending upon hard impacts and  keep everything aligned. 

Designed only for the 2021 + Honda CRF450R chassis & the 2022+ CRF250R Chassis -** does not work on older chassis or the 2021 CRF250R chassis.

Our kit requires No welding!  You can re-install a 450 motor into this bike even after converted* 

Bolt in engine cradle kit using CR500 components (engine, carburetor, electrical, exhaust etc) 

Works with the 89-01 CR500 Engine 

 

This is just the standard kit with the main components, minus the radiators and the intake parts and pieces. You can get your own radiators and modify your own intake if you would prefer to. 

This kit includes: 

Billet Cradle Brackets 

Front Upper Cradle Bolts

Middle Cradle Bolt 

Lower Cradle Bolt

Nylon Nuts

Swingarm Spacers 

Fabricated Headstay (Required to work with our cradle brackets)

Billet Fuel Tank Flange (You will use the OEM hardware from the bike) 

Exhaust Spacer and bolt 

 

Petcock Information below (to be purchased separately)

Part Number: 16955-MEB-671 (Joint Assy, Fuel)

Part Number: 16997-467-000 (O-ring 11.8 x 3.55)

Part Number: 96001-06016-00 (Bolt, Flange 6x16)

 

Works with the 09-16 CRF450R Kickstarter (Not Included)

 

 

 

Designed only for the 2021 + Honda CRF450R chassis -** does not work on older chassis** 

Our kit requires No welding!  You can re-install a 450 motor into this bike even after converted* 

Bolt in engine cradle kit using CR250 components (engine, carburetor, electrical, exhaust etc) 

Included in our Full kit : 

-Billet aluminum lower engine cradles (left & Right) 

-motor mount bolts / hardware

-fabricated / tig welded head stay 

- Billet fuel tank flange  (converts tank to gravity fed + honda pet cock) 

-Billet swing-arm spacers 

-Billet hose extenders/ coolers 

-Radiator locator brackets (designed for CR250R radiators to fit 21 chassis) + spacers

-Aftermarket CR Radiators (we modify them to work on this chassis) 

- Billet hose fitting for CR radiator 

- Billet exhaust hanger bracket spacer

-exhaust hanger bracket and hardware 

-silicone intake boot , Custom fabricated intake tube 2.5-3” and 3” to 4” silicone 90 to a 4” Air filter + outerwear  (please look at our youtube video for details)  **this eliminates the need for a restrictive box , and still has all the protection of one using the oem pcs to completely enclose it ** 

**************************************************

PARTS NOT INCLUDED that you need to source: 

- 2021+ CRF450R chassis 

-CR250 engine (95-01 is easiest) 

-CR250 intake boot/reeds/carburetor 

-CR250 electrical (harness-cdi -stator etc) 

-CR250 Coolant Hoses (Radiator hoses)

-CR250 shift lever 

-CR250 controls/clutch cable/ throttle etc

-CR250 exhaust  + silencer  (This kit works with 2001 pipe and silencer - no modifications necessary, we will include the mounting brackets

-OEM honda fuel line flange + o-ring ( that bolts to our main flange)

-misc hardware -  a skilled mechanic with experience of a CR250  , 2 strokes, jetting etc.....

USES 09-16 CRF450R KICK STARTER (NOT INCLUDED) 

 

Petcock Information below (to be purchased separately)

Part Number: 16955-MEB-671 (Joint Assy, Fuel)

Part Number: 16997-467-000 (O-ring 11.8 x 3.55)

Part Number: 96001-06016-00 (Bolt, Flange 6x16)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 Designed only for the 2021 + Honda CRF450R chassis & 2022 CRF250R chassis and up-** does not work on older chassis or the 2021 CRF250R chassis** 

Our kit requires No welding!  You can re-install a 450 motor into this bike even after converted* 

Bolt in engine cradle kit using CR500 components (engine, carburetor, electrical, exhaust etc) 

Base Price includes ONLY: 

-Billet aluminum lower engine cradles (left & Right) 

-Billet swing-arm - engine case locating spacers (***required spacing for cradles***) 

 

Now choose options (to build your kit how YOU want) 

- ( ENGINE BOLT KIT ) motor mount bolts / hardware

-( HEAD STAY KIT ) Fabricated / tig welded HEAD STAY (pick your year) 

- ( FUEL PUMP FLANGE KIT ) Billet fuel tank flange (converts tank to gravity fed + honda pet cock) 

- (EXHAUST MOUNTING KIT) Billet exhaust spacer + bolt (for oem exhaust hanger)  - exhaust hanger bracket and hardware  (for mid pipe) - includes reducer spacer, rubber mounting and hardware. 

- ( PRE-WELDED RADIATOR KIT ) include Aftermarket CR Radiators (we modify them to work on this chassis) with Radiator locator brackets (designed for CR250R radiators to fit 21 chassis) + spacers, Billet hose extenders/ coolers

-( INTAKE KIT )  includes -silicone intake boot , Custom fabricated intake tube 2.5-3” and 3” to 4” silicone 90 to a 4” Air filter + outerwear  (please look at our youtube video for details)  **this eliminates the need for a restrictive box , and still has all the protection of one using the oem pcs to completely enclose it ** 

**************************************************

PARTS NOT INCLUDED that you need to source:

- Billet Aluminum midpipe bracket, as shown in picture, is not included. It is an OEM Honda part. We show this for reference to showcase the hardware that we do include for that bracket. You will need to source the OEM bracket and rubbers on your own. Below are the part numbers for what is needed:

Stay, Chamber - 18355-KZ3-J40 (QTY 1)

Rubber, Muffler - 18334-KA3-830 (QTY 2)

Collar, Muffler Setting - 18336-KS6-700 (QTY 2)

 

- 2021 CRF450R chassis 

-CR500 engine (89-01 is easiest) 

-CR500 intake boot/reeds/carburetor 

-CR500 electrical (harness-cdi -stator etc) 

-CR500 Coolant Hoses (Radiator hoses)

-CR500 shift lever 

-CR500 controls/clutch cable/ throttle etc

-CR500 exhaust  + silencer  (you must modify silencer mid pipe to work with this chassis)  we are coming out with our own soon!  

-OEM honda fuel flange o-ring ( that bolts to our main flange)

-misc hardware -  a skilled mechanic with experience of a CR500  , 2 strokes, jetting etc..... please do research on CR500 - watch all of our 500 content  and learn about the process before emailing. 

USES 09-16 CRF450R KICK STARTER (NOT INCLUDED) 

 

Petcock Information below (to be purchased separately)

Part Number: 16955-MEB-671 (Joint Assy, Fuel)

Part Number: 16997-467-000 (O-ring 11.8 x 3.55)

Part Number: 96001-06016-00 (Bolt, Flange 6x16)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 Designed only for the 2021 + Honda CRF450R chassis & 2022 CRF250R chassis and up-** does not work on older chassis or the 2021 CRF250R chassis** 

Our kit requires No welding!  You can re-install a 450 motor into this bike even after converted* 

Bolt in engine cradle kit using CR500 components (engine, carburetor, electrical, exhaust etc) 

Kit Includes:

-Billet aluminum lower engine cradles (left & Right) 

-Billet swing-arm - engine case locating spacers (***required spacing for cradles***) 

- ( ENGINE BOLT KIT ) motor mount bolts / hardware

-( HEAD STAY KIT ) Fabricated / tig welded HEAD STAY (pick your year) 

- ( FUEL PUMP FLANGE KIT ) Billet fuel tank flange (converts tank to gravity fed + honda pet cock) 

- (EXHAUST MOUNTING KIT) Billet exhaust spacer + bolt (for oem exhaust hanger)  - exhaust hanger bracket and hardware  (for mid pipe) - includes reducer spacer, rubber mounting and hardware. 

- ( PRE-WELDED RADIATOR KIT ) include Aftermarket CR Radiators (we modify them to work on this chassis) with Radiator locator brackets (designed for CR250R radiators to fit 21 chassis) + spacers, Billet hose extenders/ coolers

-( INTAKE KIT )  includes -silicone intake boot , Custom fabricated intake tube 2.5-3” and 3” to 4” silicone 90 to a 4” Air filter + outerwear  (please look at our youtube video for details)  **this eliminates the need for a restrictive box , and still has all the protection of one using the oem pcs to completely enclose it ** 

**************************************************

PARTS NOT INCLUDED that you need to source:

- Billet Aluminum midpipe bracket, as shown in picture, is not included. It is an OEM Honda part. We show this for reference to showcase the hardware that we do include for that bracket. You will need to source the OEM bracket and rubbers on your own. Below are the part numbers for what is needed:

Stay, Chamber - 18355-KZ3-J40 (QTY 1)

Rubber, Muffler - 18334-KA3-830 (QTY 2)

Collar, Muffler Setting - 18336-KS6-700 (QTY 2)

 

- 2021 CRF450R chassis 

-CR500 engine (89-01 is easiest) 

-CR500 intake boot/reeds/carburetor 

-CR500 electrical (harness-cdi -stator etc) 

-CR500 Coolant Hoses (Radiator hoses)

-CR500 shift lever 

-CR500 controls/clutch cable/ throttle etc

-CR500 exhaust  + silencer  (you must modify silencer mid pipe to work with this chassis)  we are coming out with our own soon!  

-OEM honda fuel flange o-ring ( that bolts to our main flange)

-misc hardware -  a skilled mechanic with experience of a CR500  , 2 strokes, jetting etc..... please do research on CR500 - watch all of our 500 content  and learn about the process before emailing. 

USES 09-16 CRF450R KICK STARTER (NOT INCLUDED) 

 

Petcock Information below (to be purchased separately)

Part Number: 16955-MEB-671 (Joint Assy, Fuel)

Part Number: 16997-467-000 (O-ring 11.8 x 3.55)

Part Number: 96001-06016-00 (Bolt, Flange 6x16)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Replacement billet rear caliper bracket for your 2004-2014 honda TRX450R. 

 

---

---

Give the gift that keeps on giving! 

A gift card is always the best gift to let your loved ones choose what they want!

- CNC Machined from Billet Aluminum 

- Includes Mounting Bolts 

- Made in the USA 

 

Fits the following Make and models:

Honda 

TRX450R

TRX250R

TRX400EX

 

Yamaha

YFZ450

YFZ450R

 

Suzuki 

LTR450

Z400 

 

You can now choose the option to upgrade to a K&N Filter.

 

Time to stop changing that expensive oem air filter! And prevent the dirt/dust from getting to it. 

now with our easy change pre filter you can easily do this out on the trail and carry a spare filter. 

see video for details: click here 

included in our kit:

-Dual stage air filter

-outerwear 

-intake tube (replaces snorkle)

-mounting flanges 

-hose clamps

-BVC Quick change cover

-push pins/hardware

-instructions (video) 

 

Video of Install Here 

 

**PLEASE ALLOW 2-4 BUSINESS DAYS PROCESSING TIME BEFORE PACKAGE GETS SENT OUT**

**bed mods required see video**

**patent pending**

 

 

 

 

 

 

Fits Honda TRX450R (ALL YEARS) 

This Billet axle nut replaces your OEM nut and rotor/disc hub  and is replaced with this complete assembly.     

Axle nut pinch to prevent nut from loosening. 

Blind hole axle nut pinch to prevent dirt from entering threads.  

Option to add an Axle Wrench, which attaches to any 1/2" ratchet wrench. 

If you choose not get the axle wrench, you can use any large crescent wrench 

CNC Machined in-house - in the USA! 🇺🇸 

 

 

The perfect beanie has arrived! This embroidered beauty has a snug fit that ensures you're going to feel cozy and warm whatever you're doing.

• 60% cotton, 40% acrylic
• Breathable cotton blend
• Form-fitting shape
• One size fits most

This super-soft crew shirt is a good choice if you're looking for a classic long sleeve t-shirt.

• 100% combed ring-spun cotton
• 32 singles
• Fabric laundered
• Set-in 1x1 baby rib collar

Size guide

Have you swapped a different motor into your can am ds450 and need to install your rear brake caliper on the opposite side?   Here is a simple solution.     We worked with jon guetter to design this product and he runs one on his personal quad.

CNC machined in-house made in usa.  

Replaces factory ignition cover

CNC machined in-house made in USA

uses oem gasket (not included) 

raw billet aluminum finish

 

 

The Stage 1 is our most accessible entry-level shock model designed to upgrade your ATV’s suspension beyond the capabilities of the stock shocks. They are ideal to replace worn out stock shocks or to upgrade the handling of your vehicle in simplicity.

 

The Stage 1 is our most accessible entry-level shock model designed to upgrade your ATV’s suspension beyond the capabilities of the stock shocks. They are ideal to replace worn out stock shocks or to upgrade the handling of your vehicle in simplicity.

 

***This is a hidden product used with the Product Options application, Please do not delete this product.***

***This is a hidden product used with the Product Options application, Please do not delete this product.***

***This is a hidden product used with the Product Options application, Please do not delete this product.***

***This is a hidden product used with the Product Options application, Please do not delete this product.***

Now offering complete Honda 4 Stroke Thumb Throttle Kits

 

It allows you to change out the twist throttle to a thumb throttle.

 

The kit includes:

Throttle Cable

Throttle housing

OEM Handlebar holder (to space out the master cylinder)

2 Bolts

 

This works on all 4 stroke Hondas ( all years) such as the following:

CRF450R

CRF450X

CRF450RL

CRF450RX

 

Fits CRF450R Kick Lever for Quad or Bike Conversions Using CRF or CR500 Engine

Check out this super sleek design on our Honda talon front bumper. 

Made out of 1 3/4 DOM tube 

Fully Tig Welded 

Powder-coated of your color choice to the colors we offer currently (more to come in the future) 

Made in House -  Made in the USA 

***This is a hidden product used with the Product Options application, Please do not delete this product.***

The Infamous - "Make America 2-Stroke Again" Long Sleeve Shirt

This super-soft crew shirt is a good choice if you're looking for a classic long sleeve t-shirt.

• 100% combed ring-spun cotton
• 32 singles
• Fabric laundered
• Set-in 1x1 baby rib collar

Size guide

The perfect beanie has arrived! This embroidered beauty has a snug fit that ensures you're going to feel cozy and warm whatever you're doing.

• 60% cotton, 40% acrylic
• Breathable cotton blend
• Form-fitting shape
• One size fits most

The infamous - "MAKE AMERICA 2-STROKE AGAIN" Graphic Tee

• 100% ring-spun cotton
• Sport Grey is 90% ring-spun cotton, 10% polyester
• Dark Heather is 65% polyester, 35% cotton
• 4.5 oz/y² (153 g/m²)
• Pre-shrunk
• Shoulder-to-shoulder taping
• Quarter-turned to avoid crease down the center

Size guide

Designed to work with the Uni or K&N Air filter for the Honda Talon intake quick change pre-filter kit.

Protects engine and air filters against dirt and debris. Hydrophobic manufacturing process repels water. Horsepower levels are maintained longer due to cleaner primary filter. Outerwears pre-filters are washable and reusable. Pre-filters are specific to filter shape, filter manufacturer and application.

Our enforcer bumper offers a unique "Truck" Style look for your Polaris Scrambler 

The BVC fab Enforcer front bumper for the Polaris Scrambler XP 1000S is built from .125 wall Steel Tubing & .125 Thick Sheet Metal bent, fabricated and Tig welded in house in the USA

Mini Texture Black Powder coat finish 

Offered in Raw Finish if you want to powder coat it your own color 

A nice addition is our Radiator Guard (Sold Separately) 

Bumper Fits 2020 - 2023 Polaris Scrambler XP 1000 Models 

 

**This is not a winch mount bumper**

Change the look of your Polaris Scrambler with our Enforcer Grille 

Fabricated Design 

CNC Cut 

Fabricated & Built in the USA

Powder coated Mini Texture black 

Available in raw finish if you want to customize your own colors 

Mounting Hardware Included 

***This is a hidden product used with the Product Options application, Please do not delete this product.***

Now you can purchase the quick change cover only. 

it will include the push pins 

 

Now offering a 6061 billet rear caliper bracket that also is a Rotor guard.  Protect that expensive rotor with this billet guard.  The lower guard is now replaceable , so only buy this assembly one time and replace the lower guard as you need it!  

 

Fits 86-89 TRX250R.  

Must use TRX450R and TRX450ER rear caliper******** 

Alignment spacer included for brake disc hub *  

• Designed to provide increased performance
• Pleated media provides a large filtration area offering long service intervals
• Multi-layers of woven cotton gauze media offers excellent filtration
• Fits directly into OEM airbox with application specific sealing bead to ensure a precise fit
• Fuel management modifications are not normally required for increased performance
• Made in the U.S.A. for over 40 years
• Washable, and reusable, pre-oiled and ready to ride

replacement rotor guard for our billet caliper mount/rotor guard assembly.  Hardware included  .  

 

Replace your OEM Swingarm Pivot Bolt with our New BVC Billet Pivot Bolt

Features:

- Heavy Duty 

- Made in USA 

- OEM Replacement 

- Includes Nylon Locking Nut & Washers 

- CNC Machined 

This t-shirt is comfortable, soft, lightweight, and form-fitting. It's an ideal staple piece for any wardrobe!

• 100% combed ring-spun cotton
• Heather Grey is 90% cotton, 10% polyester
• Fabric weight: 4.3 oz/yd² (145.8 g/m²)
• 32 singles
• Pre-shrunk
• Blank product sourced from Honduras, Nicaragua, Mexico, or Cambodia

Size guide

TRX250R full gusset kit

now including lower and front motor mounts.  You must cut/remove your oem mounts to install ours.

Welding skills-fab skills required!  

TRX250R gusset kit

Welding skills-fab skills required!  

instructions included 

standard kit,  do you need front motor mounts too? Check out our other kit 

This air-filter is designed for the Honda Talon Quick Change filter system

This 2-stage filtration increases performance and engine life. Dual filters trap dirt, keep motors running clean even under the most severe conditions.

 

 

This is an aluminum Radiator Outlet tube

Made out of 6061 Aluminum 

It's a universal Weld On - Cut to Fit 

Fits 1/4" Hose 

This is an aluminum Radiator Outlet tube

Made out of 6061 Aluminum 

It's a universal Weld On - Cut to Fit 

Fits 5/8" Hose 

This is an aluminum Radiator Outlet tube

Made out of 6061 Aluminum 

It's a universal Weld On - Cut to Fit 

Fits 7/8" Hose 

Now offering complete YZ250 2 Stroke Thumb Throttle kits

 

It allows you to change out the twist throttle to a thumb throttle.

 

The kit includes:

Throttle Cable

Machined spacer for the end of the cable

Throttle housing

OEM Handlebar holder (to space out the master cylinder)

2 Bolts

Now offering a 6061 billet rear caliper bracket that also is a Rotor guard.  Protect that expensive rotor with this billet guard.  

The lower guard is now replaceable , so only buy this assembly one time and replace the lower guard as you need it!  

***FITS YAMAHA YFZ450R *** efi models 2009 +